admin, auteur op wifinederland.nl • Pagina 12 van 12

SXT 5HND Point to Point MPLS

2020

This is an example shows how the bridge be done using MPLS instead of WDS. Bridge: /interface wireless set wlan1 adaptive-noise-immunity=ap-and-client-mode band=5ghz-onlyn basic-rates-a/g=”” country=australia disabled=no frequency=5180 frequency-mode=manual-txpower ht-ampdu-priorities=0,1,2,3,4,5,6,7 ht-extension-channel=below-control ht-rxchains=0,1 ht-txchains=0,1 mode=bridge rate-set=configured ssid=wifinederland.nl supported-rates-a/g=”” wireless-protocol=nv2 /ip address add address=172.16.0.1/30 interface=wlan1 /mpls ldp set enabled=yes lsr-id=172.16.0.1 transport-address=172.16.0.1 /mpls ldp interface add interface=wlan1 /interface vpls add…
Lees verder

Mikrotik Simple point to point Networks with SXT

2020

Bridge config – Master /interface bridge add mtu=1500 name=bridge1 /interface wireless security-profiles set [ find default=yes ] supplicant-identity=master add authentication-types=wpa-psk,wpa2-psk eap-methods=”” \ management-protection=allowed management-protection-key=12345 \ mode=dynamic-keys name=profile1 supplicant-identity=”” \ wpa-pre-shared-key=12345 wpa2-pre-shared-key=12345 /interface wireless set [ find default-name=wlan1 ] band=5ghz-a/n channel-width=20/40mhz-Ce \ country=netherlands disabled=no frequency=5200 mode=bridge rx-chains=0,1 \ security-profile=profile1 ssid=wifinederland_5ghz_lijn1 tx-chains=0,1 /ip ipsec proposal set […
Lees verder

Mikrotik rb3011 I.C.M Provider Tweak glasvezel

2020

Hier is een configuratie van mijn mikrotik i.c.m. provider tweak internet-tv-telefoon Let op de mac adressen gebruik je eigen. Voor vragen kan je altijd mailen naar info@wifinederland.nl Telefoon sip account heb ik in een los toestel geprogrammeerd en dit werkt goed. De standaard zyxel router van provider Tweak heb ik er tussen uitgehaald . #…
Lees verder

InterVLAN routing MikroTik

2020

If separate VLANs are implemented on a switch, then a router is required to provide communication between VLANs. Switch works at OSI layer 2 so it uses only Ethernet header to forward and does not check IP header. For this reason we must use the router that is working as a gateway for each VLAN.…
Lees verder

Q-in-Q MikroTik

2020

Original 802.1Q allows only one vlan header, Q-in-Q on the other hand allows two or more vlan headers. In RouterOS Q-in-Q can be configured by adding one vlan interface over another. Example: /interface vlan add name=vlan1 vlan-id=11 interface=ether1 add name=vlan2 vlan-id=12 interface=vlan1 If any packet is sent over ‘vlan2′ interface, two vlan tags will be…
Lees verder

Port based VLAN tagging (Trunk and Access ports) MikroTik

2020

Add necessary VLAN interfaces on ethernet interface to make it as a VLAN trunk port. /interface vlan add interface=ether2 name=eth2-vlan200 vlan-id=200 add interface=ether2 name=eth2-vlan300 vlan-id=300 add interface=ether2 name=eth2-vlan400 vlan-id=400 Add bridges for each VLAN /interface bridge add name=bridge-vlan200 add name=bridge-vlan300 add name=bridge-vlan400 Add VLAN interfaces to their corresponding bridges and ethernet interfaces where untagged traffic…
Lees verder

In en uitschakelen van de Mikrotik interfaces

2020

Dit script kan gebruikt worden zowel in scheduler, netwatch of in het terminal venster. Ethernet interface in en uit schakelen Ethernet interface ON /interface ethernet enable ether1 Ethernet interface OFF /interface ethernet disable ether1 Wireless interface Wireless interface ON /interface wireless enable wlan1 Wireless interface OFF /interface wireless disable wlan1 Automatisch uit en aan zetten…
Lees verder

Auteur: admin

SXT 5HND Point to Point MPLS

Mikrotik Simple point to point Networks with SXT

Mikrotik rb3011 I.C.M Provider Tweak glasvezel

InterVLAN routing MikroTik

Q-in-Q MikroTik

Port based VLAN tagging (Trunk and Access ports) MikroTik

In en uitschakelen van de Mikrotik interfaces

Schrijf je in voor de nieuwsbrief

Links

Contact

wifinederland.nl